If you are deciding between a Ritchie WaterMatic and a Miraco LilSpring, the short answer is that they are an apples to apples comparison. Both series are insulated poly automatic waterers built in Iowa, both come standard without heat and take the same kind of heat package, and across the two lineups almost every model has a close match in the other. This page puts them side by side so you can see the sizes together and decide on what actually differs.
Both lines have been in the field a long time and parts are available for new and older units, so neither one leaves you stranded. Installation is the same work either way.


Every unit here comes standard without heat
That is the first thing to settle, because it is where most of the confusion starts. Across both series the waterer ships as an unheated insulated fountain. If you are in an area that gets freezing weather, or you want the extra protection, you add the heat package.
The heat package is the same idea on both brands: an immersion heater that sits in the trough and a self regulating heat cable for the water line. Ritchie sells it as the Ritchie Heat Package for poly units. Miraco sells it as the Miraco 160 heater kit at 290 watts, 120V, along with 220 volt and 540 watt versions. On several of the LilSpring models we also list the factory heated version so you can order the unit complete instead of buying the parts separately.
Sizing the heat
Follow the manufacturer instructions for your model and your local electrical code, and we recommend having an electrician run the electricity. The wattage is published on each product page so you can size the service before the wire goes in.
What the two series have in common
- A one piece insulated poly body with a sealed, sloped bottom.
- Urethane insulation 2 to 3 inches thick, rated at R-7 per inch, in both brands.
- A side access panel that gets you to the water line and the heater without digging anything up.
- A trough that slopes to a large 3 inch drain plug, so clean out is a pull and a rinse.
Where the two series actually differ
If the units are this close on size, capacity and insulation, what is left to choose on? Three things.
1. How you get into the valve chamber
Both are tool free. They just go about it differently.
On the Ritchie WaterMatic the cover lifts out, and there is no gasket involved. The cover sits in a water seal groove that you fill with water or oil, and the liquid in that groove is what seals the cover against the wind and keeps the cold air out. To take the cover back off in cold weather, give the top a tap with a rubber mallet to break it loose and lift it out. Nothing to unbolt, and no seal to replace.
On the Miraco LilSpring, two spring loaded clamps on the side hold the valve chamber cover down. Pull the clamps and the cover comes off. Nothing to fill and nothing to tap loose in the cold.
What seals a LilSpring cover against the wind is a gasket between the cover and the body, and that makes it a wear part. A gasket that has worn, torn or gone missing is no longer sealing the cold air out, so it is worth a look when you have the cover off anyway. We stock it as the 179 valve compartment gasket, and the rest of them are in Miraco gaskets.
Which one is better?
Neither, and that is the honest answer. The Ritchie asks you to keep liquid in the groove and carry a rubber mallet. The Miraco asks you to work two clamps and keep a gasket in good shape. Pick the routine you would rather do in January.
2. Anchor bolts
Both mount to a concrete pad, but they arrive differently. Miraco includes stainless steel anchor bolts with the unit. Ritchie gives you anchor pockets in the base and you supply your own anchor bolts, purchased separately. Worth knowing before install day, because it is the kind of thing nobody notices until the unit is sitting on the pad.
3. The valve, and how each brand handles water pressure
This is the difference that shows up in how the unit runs, and the two brands take opposite approaches.
Miraco uses one valve across the line. Every ground mounted unit in the Miraco series takes the 521 grey valve, which covers 40 to 80 PSI on its own. The exception is some of the BIGspring units, which use a different valve series. Above 80 PSI there is the 519 Ultra valve for 80 to 90 PSI. One part number, one spare on the shelf.
Ritchie matches the valve to your water pressure. The smaller WaterMatic units, the 100, 150 and 150S, use the 1/2 inch valve series and ship with the red 12575 at 40 to 60 PSI as standard. On city water or any higher pressure line you fit the green 13597 at 60 to 80 PSI instead, and it is a straightforward swap. The larger WaterMatic 300 and 1000 use the 3/4 inch series and ship with the green 15377 high pressure valve as standard, so there is nothing to change out.
Choosing within the Ritchie series also buys you flow. In the 1/2 inch series the red 12575 moves about 3.4 gallons per minute and the green 13597 about 1.45. In the 3/4 inch series the red 11101 moves about 20 gallons per minute and the green 15377 about 16.5, which is part of how the 300 and the 1000 keep up with the herd counts they are rated for.
Measure at the waterer, not at the source
The pressure at the house or the well is not the pressure at the waterer, and city pressure moves through the day. Take the reading at the unit, at a few different times, before you settle on a valve.
Model for model, drawn to the same scale
Every drawing below is to the same scale, so you can compare across the page as well as within a pair. The dashed line is the drinking height from the ground. Dimensions are from each manufacturer.
WaterMatic 100 and LilSpring 2800
Single trough for a stall, pen or small group
WaterMatic 150S and LilSpring 2700
The goat and sheep unit. Low drink height, and both of these carry a domed cover so the animals cannot climb or stand on top
WaterMatic 150 and LilSpring 2900
Double sided, for a fence line between two pens
WaterMatic 300 and LilSpring 3100
Larger single trough for a fence line or a bigger group
WaterMatic 1000 and LilSpring 3500
Square all around drinker for the biggest groups
Two LilSpring models with no WaterMatic match
The LilSpring 3000 and the LilSpring 3200 sit between the Ritchie sizes. The 3000 is a compact single trough with a short footprint, useful where there is not room for a longer unit. The 3200 is a long 48 inch trough at 25 gallons with access panels at both ends.
LilSpring 3000 and LilSpring 3200
Miraco only, no WaterMatic equivalent
Full specifications side by side
| Model | Capacity | Drink height | Footprint L x W x H | Weight | Rated for | Price |
|---|---|---|---|---|---|---|
| Single trough for a stall, pen or small group | ||||||
| WaterMatic 100 #18165 | 2.8 gal (10.6 L) | 18 in (45.7 cm) | 24.5 x 14 x 23.5 in | 38 lb | 20 horses, 20 beef, 50 sheep | $449.99 |
| LilSpring 2800 | 4 gal (15.1 L) | 19 in (48.3 cm) | 20 x 16 x 27.5 in | 40 lb | 30 beef or horses | $374.99 |
| The goat and sheep unit | ||||||
| WaterMatic 150S #18222 | 4.2 gal (15.9 L) | 13 in (33 cm) | 33.5 x 14 x 22 in | 41 lb | 100 sheep, 100 goats | $525.00 |
| LilSpring 2700 | 6 gal (22.7 L) | 14 in (35.6 cm) | 28.75 x 17.5 x 24.5 in | 40 lb | 100 sheep or goats | $425.00 |
| Double sided, for a fence line between two pens | ||||||
| WaterMatic 150 #18166 | 4.2 gal (15.9 L) | 18 in (45.7 cm) | 34 x 14 x 24 in | 50 lb | 40 horses, 40 beef, 100 sheep | $525.00 |
| LilSpring 2900 | 6 gal (22.7 L) | 19 in (48.3 cm) | 30.5 x 16.5 x 27.5 in | 48 lb | 60 beef or horses | $424.99 |
| Larger single trough for a fence line or a bigger group | ||||||
| WaterMatic 300 #18050 | 8.2 gal (31 L) | 26 in (66 cm) | 36 x 21.5 x 31 in | 71 lb | 125 horses, 125 beef, 60 dairy | $719.00 |
| LilSpring 3100 | 8 gal (30.3 L) | 22 in (55.9 cm) | 36 x 22 x 27.5 in | 75 lb | 100 beef or 50 dairy | $549.99 |
| Square all around drinker for the biggest groups | ||||||
| WaterMatic 1000 #18110 | 22 gal (83.3 L) | 26 in (66 cm) | 42 x 42 x 32 in | 129 lb | 275 beef, 135 dairy | $1,029.00 |
| LilSpring 3500 | 40 gal (151.4 L) | 26 in (66 cm) | 42 x 42 x 32 in | 145 lb | 225 beef or 110 dairy | $910.00 |
| Miraco only, no WaterMatic equivalent | ||||||
| LilSpring 3000 | 5 gal (18.9 L) | 16 in (40.6 cm) | 24 x 22 x 21 in | 48 lb | 30 beef, 30 horses, 50 sheep | $380.00 |
| LilSpring 3200 | 25 gal (94.6 L) | 24 in (61 cm) | 48 x 22.5 x 29 in | 98 lb | 150 beef or 75 dairy | $704.00 |
Capacities, dimensions and herd ratings are the manufacturer published figures for the unheated unit. Prices shown are current as of November 19, 2026, for the standard unheated model. Follow the model link for the live price, color options and the factory heated version where one is offered.
So how do you choose?
Once you have the pair narrowed down, the things that actually move the decision are these.
- Price. In most of these pairs the LilSpring comes in lower on the unheated unit. Compare the pair you need rather than the series as a whole, because the gap is not the same at every size.
- Trough capacity against drinking space. More gallons in the bowl is not the same thing as more animals served. Refill rate and how much trough edge the animals can reach matter just as much. The 1000 and the 3500 share the same 42 by 42 inch footprint, and the 3500 holds more water while the 1000 refills from the Ritchie valve.
- Your water pressure. Take the reading at the waterer. If it sits above 60 PSI, a Ritchie needs the green valve and a Miraco does not need anything changed.
- What you already own. If every other waterer on the place is one brand, staying with it means one set of repair parts on the shelf instead of two.
Common questions
Is a Ritchie WaterMatic or a Miraco LilSpring better?
Neither one is better across the board. They are built the same way, insulated to the same R-7 per inch, and almost every model in one series has a close match in the other on capacity and drinking height.
What actually decides it is the price on the pair you need, the drinking height against your animals, how your water pressure lines up with each brand's valve, and which brand you already stock parts for.
Which LilSpring is equivalent to my WaterMatic?
Matching them by size and use: the WaterMatic 100 lines up with the LilSpring 2800, the WaterMatic 150S with the LilSpring 2700, the WaterMatic 150 with the LilSpring 2900, the WaterMatic 300 with the LilSpring 3100, and the WaterMatic 1000 with the LilSpring 3500.
The LilSpring 3000 and 3200 have no WaterMatic counterpart.
Do these waterers come with heat?
No. Both series come standard as an unheated insulated unit, and you add the heat package where you want freeze protection. On several LilSpring models a factory heated version is also listed so the unit arrives complete.
Can I use one of these without any heat?
In a climate that does not freeze, yes. Where it does freeze, the manufacturers call for the heat package. These are insulated fountains rather than energy free designs, so they are not intended to run through a hard winter on herd turnover alone. Check the instructions for your model.
There is a middle case worth knowing about. In a mild climate where it only freezes now and then, and you just want some supplemental protection, the immersion heater on its own is usually all that is needed rather than the full package with the heat cable.
Which one has the lower drinking height for goats and sheep?
The Ritchie WaterMatic 150S sits at 13 inches (33 cm) and the Miraco LilSpring 2700 at 14 inches (35.6 cm). Both are rated by their manufacturers for up to 100 sheep or goats. A cattle unit at 22 inches or more will be too tall for most flocks.
Are parts still available for older units?
Yes, for both series, current and older units. If you are not sure which version you have, use the parts list for your model below and match the valve and the float before you order. The WaterMatic 300 and 1000 each have a separate pre-2019 parts list, because the valve changed.
Is the installation different between the two brands?
No. Both need the supply line brought up below frost depth inside a riser tube, a level pad to anchor to, and the electricity run to the unit if heat is being added. Nothing should be backfilled inside the riser tube, and nothing should touch both the water line and the wall of the tube, because that contact is what lets frost carry across to the line.
How many gallons does the trough need to hold for my herd?
Less than people expect. Bowl capacity does not have to equal the herd's daily demand, because the valve refills the trough as the animals drink. What matters is the refill rate and how many animals can reach the trough at once. Use the manufacturer herd rating for the model as your starting point.
Parts for either one, by model
Whichever way you go, the parts are here. Each list below is built around one model so you can see the valve, the float, the gaskets, the drain plugs and the heat parts that belong to your unit.
Ritchie WaterMatic
Still deciding
If you want a second opinion on a pair, tell us the species, the head count, where the unit is going and your winter lows, and we will tell you which of the two we would put there. Use the contact form and we will get back to you.
Shop the full lineups: the Ritchie WaterMatic series and the Miraco LilSpring series. Comparing the larger ball units instead? See Ritchie Thrifty King vs Miraco MiraFount and E-Fount. Not sure which unit suits your operation at all? Start with Best Waterer to Buy.
Specifications and prices last reviewed November 19, 2026.











