These are the ball units, the energy free pasture waterers. Comparing them is harder than comparing the small enclosed units, and not because the specifications are complicated. It is because the single most important decision, whether the unit will ever have heat, has to be made before the hole is dug. This page lays the two series side by side and starts with that decision rather than burying it.
Both series are built in Iowa, both are insulated to the same standard, and parts are available for current and older units in both lines. Across the two lineups almost every Thrifty King has a MiraFount that matches it on head count and opening count.


Start with heat, because it is the one thing you cannot change later
Used without heat, both series are use based. The warmth that keeps them open through the winter comes from the water the animals move through them, and that is the whole mechanism. Energy free is not a property of the waterer on its own. It is the waterer plus the herd.
The ground will not do this for you
Worth saying plainly, because it is the most common reason an energy free unit disappoints the person who bought it. Ground warmth dissipates as it rises toward the surface, and what is left by the time it reaches the waterer is not enough to hold off a freeze on its own. Something has to put heat back in.
On a thermal tube installation it is the incoming water warming the airspace inside the tube, which we go through in Earth Tubes, Thermal Tubes and Heat Tubes. On an energy free waterer it is the incoming water arriving every time an animal drinks. Either way it is the water that does the work, not the dirt.
Here is the number that makes it concrete. An unheated unit sitting idle loses roughly one degree per hour. A unit with enough head on it never gets the chance to cool down. A unit with too few head does, and no amount of insulation changes that arithmetic.
Where the two brands differ is in what happens if you get that call wrong, or if your operation changes.
Ritchie Thrifty King
The Thrifty King takes an immersion heater and a self regulating heat cable as an option. The catch is the electricity. It has to be run to the unit at the time of installation. Adding heat to a unit that was installed without power is very difficult, because the wire has to reach a waterer already set on its pad over a buried line.
Miraco MiraFount and E-Fount
Miraco splits it into two products instead of one with an option. The MiraFount is the energy free unit. The E-Fount is the same waterer with heat built in, a 75 watt element and thermostat, and that is how you buy a heated one. Adding heat to a MiraFount after it is installed is very difficult for the same reason, so the choice is made at the order, not later.
If the unit is already in the ground and you need heat now
There is a way out on the Miraco side. Part 250 is Miraco's 250 watt immersion heater with a drain plug on the cord. It is the same 250 watt 543 immersion heater Miraco uses elsewhere, fitted with a 2 inch plug that feeds in through the drain hole from the inside, so it fits all the Miraco ball waterers. It is thermostatically controlled and it goes in without pulling the unit.
You still have to get power to it, and that line should run in conduit so animals cannot reach it and it cannot be damaged. It is not as good as having bought the heated unit, but it is a real solution when the alternative is digging the waterer back out.

The advice we give on every one of these
These are long term installations. A waterer set on a pad today will very likely still be there in ten or twenty years, and your operation will not be the same. Herd numbers change. Pens get repurposed. A unit that comfortably met its head count can end up on a handful of animals.
So run the electric to the unit at installation even if you do not intend to use it. On the Miraco side, the safest version of that is to buy the E-Fount and simply leave the heat switched off until the day you need it. If you go with the MiraFount instead, be confident about the head count on that unit for the long run, not just for this year.
What the two series have in common
- Both built in Iowa, and both have been in the field long enough that you will find thirty year old units still working.
- Parts available for current and older units in both lines.
- Urethane insulation 2 to 3 inches thick, rated at R-7 per inch, with extra depth over the valve chamber. Both are built for energy efficiency, which is the point of the design even when you do add heat.
- A high impact polyethylene shell over a foam insulated base. On both, the foam is fully sealed inside the plastic, so rodents, pests and weather cannot get at it and deplete the insulation over the years.
- Closures over every drinking opening, so the water is covered between drinks rather than open to the wind.
The closures, and the one that you can see from the truck
This is the difference owners actually talk about, and it is worth understanding before you choose.
Ritchie uses elliptical closures that tip. They take roughly 5 ounces of pressure to move aside. The current ribbed elliptical closure 16646 is a thicker walled plastic rather than an insulated one, and it is ribbed so water drains back into the trough instead of sitting on the edge and building ice. Ritchie also sells the earlier elliptical closure 16305.
Miraco uses round ball closures. They take roughly 5 pounds of pressure to push down, and the balls themselves are insulated.
Why some people will only buy the Miraco
Set correctly, both brands sit the same way. The closure rides about 1/2 to 1 inch below the rim, which is where Ritchie says to position the elliptical closures and where the Miraco balls belong too. Ritchie notes that at that height water washes off the side instead of pooling on the edge, and the movement helps keep things from freezing.
The difference is what you can see from there. A blue ball still shows above the trough at that setting, so driving past at first light or last thing at night tells you at a glance that the unit is working and the water is up, without getting out of the truck. The elliptical closures sit low against the red rim, so a drive by tells you nothing and you have to stop and look in.
On a place with waterers spread across several pastures, that one difference decides it for a lot of people.
On heat retention the gap is smaller than the insulated against not insulated wording suggests. The Miraco ball is insulated, and the Ritchie closure is a heavy thick walled plastic. Both are there to hold warmth in the trough and to cut evaporation in summer.
How each one seals the valve chamber
Same split as the rest of these two brands, and it comes down to groove against gasket.
Ritchie uses a water seal groove and no gaskets at all. You fill the groove with water or oil for the winter, and that liquid is what stops cold air getting in around the cover. Nothing to wear out and nothing to replace.
Miraco uses gaskets. They do the same job, keeping the cold air out, and they are a wear part. A gasket that is worn, torn or missing is no longer sealing, so it is worth a look when you have the cover off anyway. We stock them under Miraco gaskets.
The gasket misunderstanding, and it is a common one
The gasket is not there to stop water leaking out. That is not its job. If you have water coming out around a gasket, the gasket is not the problem: the water level is set too high. Check the float setting before you order a gasket.
What the gasket does is keep cold air from getting at the water from the inside.
Converting to an open trough in summer
This is one place where the two brands genuinely do different things, and it may matter more to you than anything else on this page.
Four of the MiraFounts convert. The 3345, 3390, 3354-S and 3370-S are built as multi use units. Take the side panels off in summer and you have an open trough that is easy to clean and gives the animals more room to drink. Put them back on for winter and you have the covered, heat holding unit again. That is built into the waterer, at no extra cost.
Ritchie does it as an accessory. The Summer Cover 18090 fits the Thrifty King CT4 and CT6, and Ritchie describes it as giving more drinking area while making the unit easier to clean. Same idea, bought separately rather than built in, and only on those two models. Note that it also fits the older CT4 bases.
So if an open trough in summer is part of what you want, the convertible MiraFounts give it to you across four sizes including the single opening 3345, while on the Ritchie side it is the CT4 and CT6 with the Summer Cover added.
Model for model, drawn to the same scale
Every drawing below is to the same scale, so you can compare across the page as well as within a pair. The dashed line is the drinking height from the ground. Dimensions and head ratings are each manufacturer's own published figures.
Thrifty King CT1 and MiraFount 3330
Single opening, for a small pasture group
Thrifty King CT2 and MiraFount 3465
Two openings, the most common pasture size
Thrifty King CT4-2000 and MiraFount 3354-S
Four openings, for a large group or a feedlot pen
Thrifty King CT6-2000 and MiraFount 3370-S
Six openings, the biggest in either series
Two of those pairs line up exactly on head count. The CT2 and the 3465 are both rated for 100 beef cattle, and the CT4-2000 and the 3354-S are both rated for 200. The Miraco holds more water in each case, the Ritchie sits taller at the drink.
MiraFounts with no Thrifty King equivalent
The Miraco line has four units that do not map onto a Thrifty King, and two of them are there for specific conditions rather than for size.
MiraFount 3345 and MiraFount 3390
Sizes that sit between the Ritchie steps, and both convert to an open trough
- MiraFount 3345 is a large single opening unit at 30 gallons, rated for 75 beef or 30 dairy. It sits above the 3330 and below the two hole units, and it converts.
- MiraFount 3390 is a two hole at 44 gallons, rated for 150 beef or 60 dairy. It fills the gap between the 3465 and the 3354-S, and it converts.
- MiraFount 3350 is the warm climate unit. Four openings, 33 gallons, rated for 180 beef or 70 dairy, and Miraco publishes no heated version of it. Do not put this one in the northern states.
- MiraFount 3340 is the sheep and goat unit. Same body as the 3330 but with four 6 inch openings and smaller 7 inch ball closures, rated for 100 head of sheep. The smaller opening is the whole point, and the heated version is the 3340E.
Miraco also builds the MiraFount 3410 and 3410-4 hog waterers, which use lift up lids rather than ball closures. Those are a different animal and a different comparison.
Full specifications side by side
| Model | Openings | Capacity | Drink height | Size L x H | Weight | Rated for | Converts | Energy free price | Heated version |
|---|---|---|---|---|---|---|---|---|---|
| Single opening, for a small pasture group | |||||||||
| Thrifty King CT1 #16271 | One | 11.2 gal | 19 in | 28 x 25 in | 61 lb | 30 beef | no | $709.00 | none |
| MiraFount 3330 | One 8.75 in. | 15 gal | 14 in | 28 x 14 in | 59 lb | 50 beef or 25 dairy | no | $620.00 | E-Fount 3330E $759.99 |
| Two openings, the most common pasture size | |||||||||
| Thrifty King CT2 #16299 | Two | 28 gal | 19 in | 43 x 25 in | 90 lb | 100 beef | no | $879.99 | none |
| MiraFount 3465 | Two 9.25 in. | 20 gal | 18 in | 36 x 18 in | 79 lb | 100 beef or 40 dairy | no | $780.00 | E-Fount 3465E $900.00 |
| Four openings, for a large group or a feedlot pen | |||||||||
| Thrifty King CT4-2000 #16430 | Four | 45.5 gal | 19 in | 43 x 25 in | 123 lb | 200 beef | no | $1,180.00 | none |
| MiraFount 3354-S | Four 9.5 in. | 70 gal | 19 in | 57.5 x 19 in | 152 lb | 200 beef or 90 dairy | Yes | $1,186.00 | E-Fount 3354-SE $1,346.00 |
| Six openings, the biggest in either series | |||||||||
| Thrifty King CT6-2000 #16440 | Six | 55 gal | 19 in | 72.5 x 25 in | 210 lb | 300 beef | no | $1,680.00 | none |
| MiraFount 3370-S | Six 9.5 in. | 100 gal | 20 in | 57.5 x 20 in | 216 lb | 250 beef or 120 dairy | Yes | $1,375.00 | none |
| Miraco only, no Thrifty King equivalent | |||||||||
| MiraFount 3345 | One 10 in. | 30 gal | 18 in | 31 x 18 in | 95 lb | 75 beef or 30 dairy | Yes | $777.00 | E-Fount 3345E $939.99 |
| MiraFount 3390 | Two 10 in. | 44 gal | 20 in | 43 x 20 in | 126 lb | 150 beef or 60 dairy | Yes | $892.00 | E-Fount 3390E $1,050.00 |
| MiraFount 3350 | Four | 33 gal | not published | not published | 90 lb | 180 beef or 70 dairy | no | $789.00 | none |
| MiraFount 3340 | Four 6 in. | 15 gal | 14 in | 28 x 14 in | 57 lb | 100 sheep | no | $700.00 | E-Fount 3340E $776.00 |
Capacities, dimensions and head ratings are the manufacturer published figures. The Thrifty King takes an immersion heater and self regulating heat cable as an option rather than a separate heated model, so its heated version column is blank by design. Prices were current on 20 November 2026. Follow a model link for the live price and color options.
Common questions
Which MiraFount matches my Thrifty King?
By opening count and head rating: the CT1 lines up with the 3330, the CT2 with the 3465, the CT4-2000 with the 3354-S and the CT6-2000 with the 3370-S.
The 3345, 3390, 3350 and 3340 have no Thrifty King counterpart. The 3345 and 3390 are extra sizes, the 3350 is warm climate only and the 3340 is built for sheep and goats.
Can I add heat to one of these later?
Plan on no, and this is the part worth getting right the first time. A Thrifty King accepts an immersion heater and a self regulating heat cable, but the electricity has to be run to the unit when it is installed. Getting power to a waterer already sitting on its pad over a buried line is very difficult.
On the Miraco side the heated unit is a different product, the E-Fount, so it is decided at the order.
There is one retrofit if you are stuck. Miraco part 250 is the 250 watt immersion heater with a drain plug on the cord, the same 250 watt element as Miraco's 543 but fitted with a 2 inch plug that feeds through the drain hole. It fits all the Miraco ball waterers. You still have to get power to it, run in conduit. It is a solution rather than the ideal.
Our advice either way is to run the electric at installation whether or not you plan to use it, because these units stay in the ground for decades and your head count will not.
How many head do I need for one of these energy free ball units?
On a ball unit like these, the rule of thumb we give is 10 head for a one or two hole unit, then about 10 head per hole above that. What you are after is enough water circulating through the day that the unit never gets the chance to lose temperature. This is a ball unit figure; the smaller enclosed fountains are a different design and a different calculation.
Check the minimum head figure in the manual for your model as well, and judge it against your lightest season rather than your fullest. A pen that runs light for part of the year is the situation where people get caught. The ground will not make up the difference.
What is the difference between the ball closures and the elliptical closures?
Pressure and visibility. Ritchie's elliptical closures tip aside under about 5 ounces of pressure. Miraco's round balls take about 5 pounds to push down.
The practical difference is that you can see the Miraco balls from a distance, so a drive past tells you the unit is working and the water is up. The elliptical closures sit below the red rim, so checking a Thrifty King means stopping and looking in.
Water is coming out around the gasket on my MiraFount. Do I need a new gasket?
Probably not. The gasket is not there to hold water in, it is there to keep cold air out. Water escaping around it almost always means the water level is set too high, so check the float setting first.
Gaskets do wear out, tear and go missing, and when that happens they stop sealing against the cold. That is when to replace one.
Which of these can I run as an open trough in summer?
Four MiraFounts convert as built: the 3345, 3390, 3354-S and 3370-S. The side panels come off for summer and go back on for winter.
On the Ritchie side the Summer Cover accessory does the same job on the Thrifty King CT4 and CT6, giving more drinking area and easier cleaning. It is bought separately and it also fits the older CT4 bases.
Is one better insulated than the other?
No. Both use 2 to 3 inches of urethane rated at R-7 per inch, with extra depth over the valve chamber, inside a high impact poly shell. On both, the foam is sealed in so rodents and weather cannot deplete it over the years. Insulation is not the thing that separates these two series.
Can I still get parts for an old one?
Yes, for both. The lists below are organized by model, including the pre-2019 and pre-2024 builds on the Ritchie side, because the valve and the closures changed over the years. Match your build before you order.
Parts for either one, by model
Whichever way you go, the parts are here. Each list is built around one model and one build year range, so you can match the valve, the float, the closures, the gaskets and the heat parts to the unit you actually own.
Ritchie Thrifty King
Miraco MiraFount and E-Fount
- MiraFount 3330 parts breakdown
- MiraFount 3340 parts breakdown
- E-Fount 3340E parts breakdown
- MiraFount 3345 parts breakdown
- E-Fount 3345E parts breakdown
- MiraFount 3350 parts breakdown
- MiraFount 3354-S parts breakdown
- MiraFount 3370-S parts breakdown
- MiraFount 3390 parts breakdown
- MiraFount 3465 parts breakdown
Before you dig the hole
Tell us the species, the head count on that pen at its lightest time of year, your winter lows and whether power can reach the spot, and we will tell you which of these two we would put there and whether to run the wire. Use the contact form.
Shop the series: Ritchie Thrifty King, Miraco MiraFount and Miraco E-Fount. Comparing the smaller enclosed units instead? See Ritchie WaterMatic vs Miraco LilSpring. Not sure which unit suits your operation at all? Start with Best Waterer to Buy.
Specifications and prices last reviewed November 20, 2026.









