Almost every call about a Miraco heater starts the same way: the waterer is icing up, the owner knows a heater is involved, and nobody is sure which of the dozen part numbers on the shelf is the right one. This guide gets you to the part number from whatever you already know, whether that is the model of your waterer, the shape of the old part in your hand, or nothing at all.
Start here: the three kinds of Miraco heat
Miraco heat comes in three forms, and knowing which one you are replacing narrows the list immediately.
- A two piece heater kit heats the water and the supply line. It is an immersion heater for the valve chamber plus a thermostat controlled cable for the valve and the line. Most heated Miraco units run this combination.
- An immersion heater alone heats only the water in the chamber. This is the element that sits down in the water.
- A cable heater alone protects the valve and the supply line. It does nothing for the water in the trough.
If your trough is freezing, you are looking at the immersion heater. If the trough is open but the line will not deliver, you are looking at the cable. If you are putting heat on a unit that never had it, you want the kit.
Find your heater by waterer model
This is the fastest route. Find your model number on the unit and read across. The model numbers are from Miraco's own parts breakdowns.
| Waterer model | Heater kit | Immersion heater | Cable heater | Also uses |
|---|---|---|---|---|
| #1000 LilFount | — | 250 (with drain plug) | — | — |
| #1100 and #1200 EquiFount | 276 silicone rubber kit | 289 silicone rubber heater | — | 285 thermostat, 295 retainer |
| #2700, #2800, #2900, #3000, #3100, #3200 LilSpring | 160 (120V) or 161 (220V), | 543 250 W | 919-5 | — |
| #3500 LilSpring | 162 (120V) or 163 (220V) | 543-5 500 W | 919-5 | — |
| #6000 to #6400 BigSpring | 162 (120V) or 163 (220V) | 543-5 500 W | 919-5 | — |
| Electric MiraFount models ending in E (#3330E, #3340E, #3345-E, #3354-SE, #3390E, #3410E, #3410-4E, #3465E) | — | 888 heat element | 919 heat cable | 887 thermostat, 893 connector |
| Heated E-Fount | — | 888 heater | — | 887 thermostat, 893 connector |
Note on the #3354-SE: Miraco's list shows two heat elements for that model, so order a pair.
Cannot find the model number?
It is on a label or stamped on the unit, usually inside the lid or on the end wall. If the label is gone, photograph the valve chamber and the old heater and send us a message. We identify parts from photos every week, and it costs you nothing but the time to take them.
Match the voltage before anything else
Miraco builds most heat parts in both 120 volt and 220 volt, and the part numbers differ only by a suffix. Getting this wrong is the most common ordering mistake we see.
| Part | 120 volt | 220 volt |
|---|---|---|
| Heater kit, lower wattage | 160 | 161 |
| Heater kit, higher wattage | 162 | 163 |
| Immersion heater, 250 W | 543 | 543/220 |
| Immersion heater, 500 W | 543-5 | 543-5/220 |
| Cable line heater | 919-5 | 919-5/220 |
| Cable line heater, 8 foot | 919-8/120 | 919-8/220 |
Read the voltage off the old part or off the plug end before you order. A 120 volt element on a 220 volt supply does not simply run hot, and a 220 volt element on a 120 volt supply will never bring the water up.
Then match the wattage
The wattage follows the size of the unit, not your preference. The smaller LilSprings take the 250 watt immersion heater; the #3500 and the BigSprings take the 500 watt. The kits carry those same elements, so the 160 and 161 kits are rated at 290 watts total and the 162 and 163 kits at 540 watts, the difference being the cable that comes with them.
Fitting a bigger element than the unit was built for does not make the trough warmer. The thermostat still decides when it runs, and you have only added draw.
Immersion heater, or immersion heater with a drain plug?
Two of the immersion heaters look alike and are not the same part. The 543 is the plain 250 watt element with a built in thermostat. The 250 is a 250 watt element that carries a drain plug in the same fitting, which is what the #1000 LilFount uses. If your old part had a plug threaded into it, you want the 250.
Do not forget the insulation
Heat you have paid for leaves through an uninsulated valve compartment. The 731 valve blanket wraps the compartment and is the least expensive thing on this page. On MiraFount models, Miraco also lists pipe insulation, part 355, for the riser.
Before you replace the element, check the thermostat
If a heater runs constantly or never comes on at all, check the thermostat before replacing the element. The thermostat is the cheaper part and it is the one that decides whether the element ever gets power. Our guide on how to test an immersion heater before winter walks through checking both, and the spring maintenance guide covers pulling the element at the end of the season.
Common questions
How do I know which Miraco heater my waterer takes?
Work from the model number on the unit and read across the table above. If the label is missing, the pairing is still predictable: the small LilSprings take the 250 watt element, the #3500 and the BigSprings take the 500 watt, the EquiFount stall waterers take their own silicone rubber heater, and the electric MiraFounts and E-Founts take the 888 element with the 887 thermostat.
What is the difference between a heater kit and an immersion heater?
The kit is two parts: the immersion heater that sits in the water plus a thermostat controlled cable for the valve and supply line. The immersion heater on its own heats only the water.
Do I need the cable heater if the immersion heater is working?
Only if the line or the valve is the thing freezing. The immersion heater warms the water in the chamber; the cable protects the plumbing that feeds it. Many units run both, which is exactly what the kit supplies.
What is the difference between the 543 and the 543-5?
Wattage. The 543 is 250 watts and the 543-5 is 500 watts. Each has a 220 volt twin, the 543/220 and the 543-5/220.
Can I put a 120 volt heater on a 220 volt supply?
No. Match the voltage to your supply and order the part number that carries that suffix.
My Miraco heater runs all the time. Is the element bad?
Not necessarily, and the thermostat is the cheaper thing to rule out first. A thermostat that has failed closed leaves the element powered continuously.
Which parts do the heated E-Fount units use?
The 888 replacement heater, the 887 replacement thermostat and the 893 wire connector.
What does an EquiFount stall waterer use for heat?
The 276 silicone rubber heater kit, or its parts individually: the 289 heater, the 285 thermostat and the 295 heater retainer assembly.
Shop and match
Every part named here is stocked: Miraco waterer heaters and thermostats. To match any other part on your unit, start from the Miraco parts lists and pick your model. If you would rather we did the matching, send us a message with your model number or a photo.